Thursday, September 25, 2014

Flagpole: the form is ready for concrete...

Flagpole: the form is ready for concrete...  And the concrete is ordered for tomorrow at noon.  My backhoe made short work of digging the big hole for the form – took me less than two hours, including finishing the details with a shovel.  Not bad for moving more than five cubic yards of heavy, wet soil!

The last step, which I finished just before dark this evening, was to position the steel sleeve in the center of the form.  You can see (in the last two photos) my system for holding it in place – using four steel wires tightened down with eye bolts to the point where they twang when plucked.  That sleeve shouldn't be moving at all when the place the concrete tomorrow.  I built a little plywood cover for the sleeve so that the concrete truck can't accidentally fill it with concrete – that would be a disaster!

Tomorrow morning I'm going to go out there and spray the inside of the form with Pam (spray canola oil) so that the concrete won't stick to the form.  I'm hopeful that I can tie ropes to the hooks on the top of the form and just yank it out with the tractor.  If that doesn't work, I'll have to tear it apart with a wrecking bar, which would be a lot more work :)


Barn: we has second story walls!

Barn: we has second story walls!  Well, two of them, anyway :)  If you're wondering why there are two holes in the floor ... one of them is for the stairwell, and the other is for a “hatch”, 10' x 5', through which I can hoist large things up into the second floor storage area...


Holes in Mars rocks...

Holes in Mars rocks...  Curiosity is drilling holes again, this time in some interesting looking rocks at the base of Mt. Sharp.  To my (very much inexpert) eye, those rocks look like petrified lake bottom, or dried mud.  I'm guessing the Curiosity science team is drilling there to figure out just what kind of rock that is...

Dust from Chad fertilizes the Amazon...

Dust from Chad fertilizes the Amazon...  It blows across the Atlantic, settles over the Amazon basin, and acts as a rich fertilizer.  But why should dust act as a fertilizer?  Turns out it's because the dust is composed largely of fish bones!

Solar sintering...

Solar sintering...  Additive manufacturing, or 3D printing, is going to be very interesting to watch develop...

Shellshock...

Shellshock...  If you run any Linux systems (especially) or other UNIX variants, you need to know about this vulnerability.  It's in bash, of all things, and it's an arbitrary code execution bug.  Nasty.  It's patch time, folks...

Google science prize awarded...

Google science prize awarded ... to three Irish teenagers who have apparently made a rather consequential discovery: a simple, inexpensive way to significantly boost the productivity of grain crops.

I keep getting surprised at how biologists, botanists, and agriculture experts (and now teenagers!) keep finding ways to boost farming yields.  Those yields have been climbing steadily and rapidly ever since the late 1800s.  Any number of times, experts have predicted that the end of these steady gains is imminent – and every time, they've been wrong.  We don't seem to have reached “peak agriculture” yet, just as we haven't reached “peak oil” or “peak silicon” yet, either...

Not so settled after all, that climate science...

Not so settled after all, that climate science...  A new paper from two prominent climatologists (Nic Lewis and Judith Curry) uses the same data the IPCC models are based on, but derives a (much) lower figure for global temperature sensitivity to carbon dioxide.  The new figure corresponds much more closely than the models to those pesky actual observations.

If you're at all interested in whether anthropogenic global warming is real, this is a must read...

Wednesday, September 24, 2014

Flagpole: it begins...

Flagpole: it begins...  In a week or so, I should be taking delivery of a beautiful tapered aluminum flagpole, 35' tall.  Said flagpole needs a sturdy base to sit in, so that winds don't blow the thing over.  The manufacturer recommends a cylinder of concrete 3' in diameter and 4' high.  Concrete is cheap, so I decided to go a tad bigger, just to add some extra stability: I'm going to place that flagpole into a 4' cube of concrete.

So how does one go about getting a 4' cube of concrete?  Well, you start by building a “form” – essentially a mold.  That's what's in the photo at right, shown in the same orientation that it will be used in.  I built that behemoth today, starting with a run to Lowe's to get the materials.  The top and bottom of this form are open.  The bottom will sit on the base of a big hole I'm going to dig tomorrow; the top is open so that the concrete truck can easily fill the form.  It all went together rather easily.  The design is about as simple as can be, and the tolerances aren't tight :)

That form isn't quite finished yet – I still have to add some wires and eye bolts to hold the steel sleeve (that actually holds the flagpole) in place while the concrete is poured.  The top of the sleeve will be in the exact center of the form, and will extend about 3/4" higher than the edges of the form.  When the concrete is poured, I'll be finishing it with a slight slope from the center to the outside, so that water will run off it easily.  The top of the form (and the edge of the concrete) will be at the same level as my yard, so I can mow around it easily.

The form will hold about 62 cubic feet (or 2.3 cubic yards) of concrete, after accounting for the space occupied by the hollow sleeve.  I'll be digging a hole that is substantially larger than that: about 6' x 6' x 4' - which means I'll be excavating about 5.3 cubic yards.  If you're familiar with bulk materials, you'll know that that's a rather large pile of dirt!  I'm very glad I'll have the backhoe to do this with.  If I had to do it by hand, I'm not entirely sure I'd survive the project :)

Communists in Oakland, California...

Communists in Oakland, California...  No big surprise there, and Zombie has the complete rundown on them.  Here's the rub, though: the socialism and communism that Zombie carefully documents here is on display at an event concerning global warming.  That's right: the global warming movement has been almost completely co-opted by the socialists/communists/progressives.

I can't help but marvel at the number of seriously deluded people on display.  Are they really so completely ignorant of recent history as to think there are answers in communism?  Then I remember: these people elected Nancy Pelosi.  Then I have to worry about it...

At over 23k, the current email regexp is getting pretty big...

At over 23k, the current email regexp is getting pretty big... Even experienced programmers skilled in the lore of regular expressions are intimidated by this monstrosity (the first few lines are reproduced below).  If I had ever seen this thing in the first few months I was using regular expressions, I'd probably have run away from them, screaming, never to return.  Just because you can validate email addresses with a regular expression doesn't mean you should...
(((?:(?:(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:\x28(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:(?:[\x01-\x08\x0b\x0c\x0e-\x1f\x7f]|[\x21-\x27\x2A-\x5b\x5d-\x7e])|(?:\x5c(?:\x0a*\x0d*[\x00-\x09\x0b\x0c\x0e-\x7f]\x0a*\x0d*)|(?:\x5c[\x00-\x7f]))))*(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?\x29))*(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:\x28(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:(?:[\x01-\x08\x0b\x0c\x0e-\x1f\x7f]|[\x21-\x27\x2A-\x5b\x5d-\x7e])|(?:\x5c(?:\x0a*\x0d*[\x00-\x09\x0b\x0c\x0e-\x7f]\x0a*\x0d*)|(?:\x5c[\x00-\x7f]))))*(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?\x29)|(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))))?(?:(?:[\x41-\x5a\x61-\x7a]|[\x30-\x39]|[\x21\x23-\x27\x2a\x2b\x2d\x2f\x3d\x3f\x5e\x5f\x60\x7b-\x7e])+(?:\x2e(?:[\x41-\x5a\x61-\x7a]|[\x30-\x39]|[\x21\x23-\x27\x2a\x2b\x2d\x2f\x3d\x3f\x5e\x5f\x60\x7b-\x7e])+)*)(?:(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:\x28(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:(?:[\x01-\x08\x0b\x0c\x0e-\x1f\x7f]|[\x21-\x27\x2A-\x5b\x5d-\x7e])|(?:\x5c(?:\x0a*\x0d*[\x00-\x09\x0b\x0c\x0e-\x7f]\x0a*\x0d*)|(?:\x5c[\x00-\x7f]))))*(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?\x29))*(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:\x28(?:(?:(?:(?:[\x20\x09]*(?:\x0d\x0a))?[\x20\x09]+)|(?:[\x20\x09]+(?:(?:\x0d\x0a)[\x20\x09]+)*))?(?:(?:[\x01-\x08\x0b\x0c\x0e-\x1f\x7f]|[\x2...

You want a computer that acts like a person?

You want a computer that acts like a person?  So do marketers!  From the linked article:
Half the time, I’m cynical/alarmed/wearied that so many people are working so hard to make machines fool humans.

But the other half the time I’m kind of cracked up by the fact that the most avid prosecutors of Alan Turing’s sly and audacious 1950 thought-experiment have been not philosophers or computer scientists or advanced A.I. labs but … marketers. The former folks have foundered for years on the difficulties of understanding the fractal contours of human consciousness. The latter just want you to open up their damn mail. Comprehending the mysteries of human thought and behavior is hard. Emulating it? Not so much! It’s partly why Turing’s test is so unsettling: Man, are we really that easy to copy?

MOM is in orbit around Mars!

MOM is in orbit around Mars!  No, not my CCPOAA mom, but the Mars Orbiter Mission – India's first interplanetary satellite.  They succeeded on their very first try, even though they were on a hurried schedule and a shoestring budget.  If they keep this up, SpaceX and Blue Ocean are going to have some offshore competition!  Here's the official announcement, and a more detailed story...

The death of free speech...

The death of free speech...  Having lived through the university protests of the '60s and '70s, I've long tended to think of the student populations as a key source of fight against censorship and other free speech restrictions.  Before these protests, universities had strict rules about what could and could not be said on campus.  The protests ended that, much to the regret of then-traditional Americans on both the left (war mongers!) and the right (flag burners!).  More liberty-minded folks (including myself) celebrate the accomplishment.

These days, though, the universities have become hotbeds of a new movement toward the suppression of free speech.  Some have dubbed this the “unfree speech movement”, and the moniker is apt.  It's a natural outgrowth of the intersection between multiculturalism and progressivism – the invention of the right not to be offended.  It's leading us down the same crazy path that Europe went down, starting 20 years or so ago.

In today's Wall Street Journal, Sol Stern – whom I remember as a radical in the '60s – has a piece that echoes my own thoughts.  It's interesting hearing what this looks like from one of those students who helped win the fight for free speech nearly 50 years ago...

Tuesday, September 23, 2014

The doorbell rings...

The doorbell rings...  Who could it be?  It's 6:30 pm, and almost time for me to get ready for bed.  Who would call on me at this hour?

I walked to the door (which is mostly glass) and outside I see a smiling Gracie, holding a plate with homemade cookies.  I didn't spot it until she'd left, but under the cookies was an envelope with a card in it.  The cookies and the card are in the photo at right (click to embiggen).  Well, to be precise, the cookies were in the photo.  Now they're in my stomach, along with a giant glass of milk.

Gracie hopes that I like sugar cookies with lots of orange cream cheese frosting.  Why, yes, Gracie.  Yes I do :)

Barn: second story shaping up...

Barn: second story shaping up...  The builders have been busy today!  Nearly all the joists are in place, the framing for the stairway and the hatch are finished except for two joists (they ran out of metal hangers), and all but a few square feet of the floor are in place (they ran out of wafer board!).  Tomorrow morning they'll finish those last details up, when the new load of lumber arrives, and then the second story walls start going up.

In the last photo below, you can see one of the builders wielding a nail gun.  After watching these guys working for the past few weeks, I think this may be the single most useful tool they have.  It's an air powered gun that holds a magazine of 250 nails.  But the best part is how it's triggered.  One mode uses a conventional trigger, just like on an actual gun.  The other mode uses pressure on the very tip – you put the nose of the gun where you want the nail and then just press gently.  A skilled user can put a nail ever 8" down the 4' length of a joist running under the floor boards in less than two seconds.  That works out to 3.5 nails per second, each one perfect straight and perfectly driven.  A skilled framer wielding a hammer might be able to do one nail every two seconds, but won't be able to sustain that for very long.  They used the same nail gun to tack all the studs in place, making very short work of that more challenging nailing job (challenging because you're nailing at close to a 45° angle)...


Rope swing optimization...

Rope swing optimization...  Let's say you had a rope swing, and you wanted to use it to go as far as possible horizontally.  How would you do it?  Here's more than you ever wanted to know about the subject...

Mann's “Hide the Decline” ruthlessly exposed...

Mann's “Hide the Decline” ruthlessly exposed...  Jean S., posting at Climate Audit, has posted a carefully researched chronology of events that exposes “Mike’s trick” as the deliberate fraud we all knew it was.  The only credible conclusion you can come to after reading Jean's awesome piece is that Mann was most definitely involved in the deliberate misleading of the IPCC, his fellow scientists, and the public at large.  His “trick” created the memorable “hockey stick” graph from the thinnest of air.  Below are two versions of the famous graph (click to embiggen): on the left without “Mike’s trick”; on the right with it...


Mike Mann, schlub scientist...

Paving: it's time for “road base”...

Paving: it's time for “road base”...  The paving guys are now doing the last step before the actual asphalt goes on: they're laying down a 3" thick layer of “road base” – a mixture of fine gravel and very fine (almost powdery) dirt.  This will be wet down and carefully smoothed to form a layer upon which the asphalt will be put down.  They'll be done with this today, but the asphalt won't go on until the paving machine is available – and I'm not sure when that is.

The first two photos below show where the ends of a 3" diameter “sleeve” are; this is partly as documentation for myself.  The idea of the sleeve is to provide a way to run pipes or wires under the pavement, without having to resort to expensive horizontal drilling.  This sleeve is 30' long, and runs diagonally under the pavement just 10' or so from our house.  Next year I hope to put a greenhouse up just west of the pavement, and when I do, I'll use this sleeve to run water and gas (and maybe electricity) out to it from the house...


Barn: the second floor progresses...

Barn: the second floor progresses...  Yesterday the builders put up the last of the glulam beams (that's one being sawed in the middle photo below), and started laying the second floor joists on top of them.  Today they've finished with the joists, including framing out a place for the stairs to go, and a place for a giant hatch (10' by 4') through which I can lift big objects with a block and tackle.  They've also started putting down the flooring. 

Things are moving along quickly on the barn!


The great water adventure...

The great water adventure...  Last night as I was just getting ready to head for bed, my phone rang.  It was my neighbor, Tim D., calling to let me know that we had a “water problem” – our neighbor's teen daughter (Gracie L.) was mowing their yard, and accidentally struck and broke one of the irrigation water “risers”.  That's precisely the same thing I had done earlier this year, so I knew exactly what it was like for Gracie :)

Tim and I talked for a couple minutes, and figured out that between the two of us we had almost everything needed to repair that broken riser, both parts and tools.  We'd need one more part, but Tim figured we could find a neighbor who had that one.  So Tim and I gathered up what we'd need, and met over where the broken riser was gushing water 20' or so high. 

As I walked up, another neighbor got the water shut off.  The geyser was gone, but a small pond remained around the broken riser.  People were gathering – adults and kids from the immediately adjacent neighbors.  Shovels and buckets appeared, and an organized effort to drain the water around the riser got started (this was necessary because the solvent used to weld PVC pipes together only works on dry pipes).  The drainage effort was made more difficult by the fact that the broken riser was near the low point of a few hundred yards of pipe, and all of that was now draining backwards through the broken riser.

Now this probably doesn't sound like a whole lot of fun, but ... we were actually all having rather a grand time.  There was much joshing and laughter.  Two dogs (Annie and Dallas) were splashing around in the water, spewing mud in every direction, splattering us all from head to foot – and we all were laughing about it. 

Eventually the draining was finished, and we got the water level down.  We used a towel to dry the pipe, then cut and glued the new parts in place.  A neighbor did have the missing part.  It was after dark by the time we finished, but I had brought a nice LED flashlight that was providing plenty of light. 

When I got home, I discovered a sad email from Gracie, the girl who had accidentally broken the riser.  She wanted to tell me just how very sorry she was for breaking my riser.  My riser?!?  Until the moment I read that email, it had never occurred to me that the broken riser was mine – but Gracie was right about that: it was on our property.  She was mowing a little piece of what I think of as their lawn when she broke the riser, but that 6' or so wide piece of lawn is actually on our property.  The whole time we were all working on that thing, I was thinking that we were all helping Gracie and her family out – but in reality that whole crew was helping me out.  What an odd feeling that was as I changed mental gears there!

I love living up here...

Mantle: it's finished!

Mantle: it's finished!  Yesterday I got the mantle, with its two corbels, mounted to the living room wall over where the fireplace will be.  I'm very pleased with the result of my mounting plate design – the finished mantle is very strong, doesn't jiggle at all, and the reclaimed wood will all be exposed once the rock is in.  The plywood mounting plates that are visible now will be completely covered by mortar and rock.  Behold (and use your imagination for the rock)!


Monday, September 22, 2014

Antarctic ice level is at an all-time record high right now...

Antarctic ice level is at an all-time record high right now...  Global warming, don't you know?

Mantle mounting...

Mantle mounting...  I spent most of this weekend (when I wasn't goofing off) working on mounting our new mantle to the living room wall.  This is a job that would have been (much) easier in a properly-equipped wood shop – but which can still be done in a garage with just hand tools.  I used saw horses and clamps to keep everything in the right place, and then a circular saw, a jig saw, and a drill.  Today I hope to actually start attaching this to the wall...

First of two plywood "plates"
Second "plate"
Installing hanger bolts
Creative clamping
Getting the hangers right
Trial fitting the finished plates
All the hangers are in

Paving progress...

Paving progress...  The first photo shows the crew “taking elevations” to determine the grade along the driveway.  This is how they make sure the water flows off the pavement the right way (away from buildings!).  The second photo shows the new apron in front of the roll-up door in the new barn.  The last photo shows the driveway near the barn, which is all finished grading and is ready for road base (a layer of gravel) and asphalt.


Portrait of a tractor...

Portrait of a tractor...  My new Kubota B26, to be precise.  This is at the request of Bob K.  The big orange thing to the left of the tractor is the 4-in-1 loader bucket, which can be exchanged in about a minute with the pallet fork currently mounted...

All in the family...

All in the family...  My brother sent this to my mom, who then sent it to all of the family, saying that there may be a message for her in this:


Ya think, mom?

Morning smile...

Morning smile...


2014 Ig Nobel awards...

2014 Ig Nobel awards...  From the Journal of Improbable Research...

Maven in orbit around Mars...

Maven in orbit around Mars...  Another little robotic explorer is about to do some serious science work for about the same cost as the useless “demonstration” 3D printer that NASA just sent to the space station.

It must be fun for the NASA honchos to waste the taxpayers' money on the vast scale that they do...

Sunday, September 21, 2014

Heavenly Sunday lunch...

Heavenly Sunday lunch...  Wash and chop into a bowl a large, ripe Cache Valley  tomato (two if small).  Sprinkle a teaspoon or so of dried Herbes de Provence over the tomato, and stir in.  Smell.  Wait five minutes or so, until you've completely recovered from ripe tomato odor intoxication, and the herbs have hydrated.  Drain and add a small can of garbanzo beans (or use some freshly hydrated ones if you were smart enough to prepare them the night before).  Add a teaspoon or two of good mayonnaise (none of that Miracle Whip crap, please!).  Stir.  Enjoy!

Snailgate...

Snailgate...  When politics intersects with science, the results are usually bad.  Delingpole explains...

Saturday, September 20, 2014

Ohio teachers are threatening to strike...

Ohio teachers are threatening to strike...  Why?  Because they're being threatened with ObamaCare!

English is so weird!

English is so weird!  Consider this sentence:
I don't have to leave now.
Then this one:
I don't have a reason to leave now.
Did you notice the word “have” is pronounced differently in these two uses?

Much more here, including other strange examples like this...

This is the kind of job that could bring me out of retirement!

This is the kind of job that could bring me out of retirement!

The most useless chemical elements...

The most useless chemical elements...  More interesting than it sounds :)

“Uncertainty is a prime mover and motivator of science and must be faced head-on.”

“Uncertainty is a prime mover and motivator of science and must be faced head-on.”  That's from an excellent and sober op-ed piece by Stephen Koonin in today's Wall Street Journal.  It's an impassioned plea by a scientist for climate scientists to act like scientists, and not ideologues – and it's especially powerful considering the source: a former Obama administration official (the undersecretary for science in the Energy Department)...

Russia captures Lithuanian ship...

Russia captures Lithuanian ship...  Not good...

The ISIS Crisis...

The ISIS Crisis...  Remy...
We could send the IRS's top IT guy.
Heh...

Friday, September 19, 2014

Amen, brother...

Amen, brother... 


Barn meets paving...

Barn meets paving...  During our home's remodeling, we've had quite a few projects that intersected.  For instance, we had to coordinate the granite installation with the vanity installation.  But this morning we had an intersection on an entirely different scale: where the paving project joins the barn project, at the big roll-up door.

Yesterday the barn builders and the paving foreman met and worked out exactly how they wanted to do it.  The paving guys, as always, were worried about how the water would run off of everything.  The builders just wanted to know what to do :)  The powwow resulted in a design for a concrete apron, sloped to the northeast, that would terminate at the correct level to meet up with the asphalt.

This morning the construction of that apron began – and just a few hours later, the concrete for it was being poured.  Meanwhile, the paving work continues apace...


The 10 Commandments...

The 10 Commandments...  Via my CCPOAA mom:
The real reason that we can't have the Ten Commandments posted in a courthouse is this -- you cannot post: 'Thou Shalt Not Steal' 'Thou Shalt Not Commit Adultery,' and 'Thou Shall Not Lie' in a building full of lawyers, judges and politicians. It creates a hostile work environment.
It would be an even more hostile work environment if I was there with them.  I'd bestow some good old-fashioned pissed-off citizen hostility!

“It's about nine months past time to acknowledge that Mr. Koskinen is the problem, not the answer...”

“It's about nine months past time to acknowledge that Mr. Koskinen is the problem, not the answer...”  Kimberley Strassel, pungent as always, pointing out the now-obvious: that the new IRS commissioner (whom I have dubbed “Mr. Smugface”) appointed nine months ago to clean up the IRS scandal is in fact leading the coverup.

“His essential problem is that he has very poor judgment... ”

“His essential problem is that he has very poor judgment... ”  Peggy Noonan continues her atonement for once having supported Barack Obama...

Remodeling: fireplace...

Remodeling: fireplace...  Much of our new home's interior work is now finished; most of what remains is “just details” – things like heating registers, electrical switch and outlet covers, lighting, etc.  But one big, messy item remains: the fireplace in our living room.

We didn't take a photo of the original fireplace, darn it.  It was a mess.  The hearth and face were both made from square tiles of greenish-gray slate, a foot on each side.  These slate tiles were very thin (about 1/4"), flaking, and poorly installed.  The hearth in particular was falling apart around the edges.  The mantle was made from a pine log, sawn like a giant piece of quarter-round molding.  One flat face was toward the wall, and the other flat face up – so the round log's exterior was facing out and down.  That might have actually made a rather nice mantle if it weren't for the fact that someone installed this before the wood was dry.  It had twisted, lengthwise, so that part of it was over an inch from the wall, and some of the top was rather dramatically tilted.

So we decided to dismantle the old fireplace and replace it.  I did the demolition work.  The slate took me about 10 minutes to completely remove – all I did was slip a putty knife under the edge of each tile and pop it off.  Sometimes four or five tiles would come off at once.  When I popped off the hearth tiles, I discovered a gorgeous piece of granite underneath them – dark green with black and gray marbling – really quite beautiful after I scraped the glue off.  Unfortunately, this granite had been installed by someone who knew what they were doing; unlike the slate, it had been very thoroughly glued down.  It was only 2 cm (less than an inch) thick, and there was no way to get it up without breaking it.  Dang.  The mantle was even harder to get off: it was mounted on three pieces of pipe that were secured into the concrete blocks of the inner fireplace.  I had to saw the mantle into three pieces while it was still on the wall, then twist each of the pieces to loosen it from the pipe mounting.  Once the pipes were exposed, I could break their glue joints by twisting with a pipe wrench.

Now we've acquired a new mantle, made from a truly beautiful piece of reclaimed chestnut wood.  I'm mounting it on the living room wall over this weekend (I hope!).  Then a local mason is going to build us a new fireplace, using random-shaped slate for the hearth, and a thin veneer of river rock (a sample of which is in the photo at right) for the face.  This “thin veneer” is an interesting technique that I didn't know about until a few months ago.  The old way of building a fireplace would use entire rocks, mortared together, to form an exterior “wall” around the inner cinder block and fire-brick construction of the fireplace.  While these fireplaces are beautiful, they are also extremely heavy – so much so that we'd have to install steel columns in the basement underneath the fireplace to hold it up, and we might even have to dig through the basement floor and install footings.  Yikes!  The “thin veneer” approach uses pieces of rock instead of the whole rock – “slices” taken from attractive faces of the rock, from 3/4" to 2" thick.  These slices have perfectly flat backs and can be arranged two-dimensionally, like puzzle pieces.  From the mason's point of view, this is vastly easier than making a wall from whole stones.  It's also far, far lighter – so much so that no extra support is needed underneath it.  The fireplace will be completed with a door we're having made by a local metal worker.

I had a difficult time finding natural stone of the type we wanted (multi-colored river rock), but I finally located a vendor in Portland, Oregon.  The market for this sort of thing is totally dominated by “manufactured” stone.  These are really just molded pieces of concrete, sometimes with some texturing material added, and dyed various colors.  Some of the manufactured stones are quite attractive, but ... they all have two degrees of uniformity that the natural stone doesn't suffer from.  One is a uniformity of shape.  Depending on which manufacturer you use, the manufactured stones come in between 8 and 24 molded shapes – so the same exactly shaped stone will appear repeatedly in one use.  The other is a uniformity of color: the manufactured stones are dyed concrete, with multi-colored variants having between 4 and 8 colors, instead of the infinite variety of shades and mottlings that one finds in natural stone.  I'm happy to have found the natural stone we wanted, from a place that will saw the thin veneers for us!